Home / SR 36-S

SR 36-S

HYDRO-COOLING SYSTEM · STANDARD CABINET SERIES

SR 36-S

Standard hydro-cooling for up to 36 miners.

A factory-built liquid-cooling system for high-density mining. It houses up to 36 Antminer hydro units and dissipates over 200 kW of heat at a design PUE below 1.05. An indoor miner rack and CDU pair with an outdoor dry cooler, pre-integrated at the factory for rapid setup.

SR 36-S hydro-cooling system render
<1.05Design PUE
>200 kWHeat dissipation
36Miner slots in one rack
>200 kWHeat dissipation capacity
<1.05Design PUE
56%Less land than 20-ft container solutions
Flexible Deployment

Indoor liquid cooling. Outdoor heat rejection.

The SR 36-S splits the system into an indoor rack-and-CDU module and an outdoor dry cooler, so heat leaves the building while the miners stay protected.

01

Indoor Rack and CDU

The 36-slot miner rack and the coolant distribution unit sit inside your facility, where climate control, security and existing buildings are part of the picture.

  • Rack and CDU deploy indoors
  • PLC console with touchscreen control
  • Adapts to constrained or existing sites
02

Outdoor Dry Cooler

The 200 kW dry cooler rejects heat outdoors through aviation-connector piping, with two large-volume fans and a standard-configuration evaporation pad.

  • Two large-volume fans
  • Variable-frequency AC fan control plus stepwise EC fan regulation
  • Rated for −4 °F to 113 °F ambient
System Architecture

Engineered as one system, not assembled from parts

Power distribution, networking, the miner rack and the coolant distribution unit arrive pre-integrated and pre-tested.

01 / PDC

Power Distribution

Miner breakers 16 A × 36. High-reliability design with high-grade copper-bar connections throughout.

02 / NETWORK

Network Switch

2 × 24-port Gigabit switches integrated in the cabinet — network-ready from day one.

03 / MINER RACK

Miner Rack

36 high-strength slots on a reinforced frame with all cabling built in, optimized for convenient maintenance.

04 / CDU

Coolant Distribution

PLC cabinet with all-in-one water tank and a 20 m³/h pump. Low-level and blowdown alarms.

70 L stainless-steel all-in-one tank with coolant observation window Water-gas separation, pressure storage and preheating built in Manual valves for quick isolation during maintenance
Why SR 34-S

A lower cost per deployed megawatt

The SR 36-S is built to cut the biggest line items in small- and mid-scale deployments: shipping, land and on-site labor.

Lower

Lower Transportation Costs

Lower shipping cost than a traditional 20-foot container solution, with the same power capacity in a smaller logistics footprint.

56%

Less Land Occupied

At the same power capacity, the SR 36-S occupies 56% less land than a 20-foot container deployment, keeping space free for the next expansion phase.

Less

Less Work, Less Time

A highly prefabricated modular design greatly reduces the work and time required on site, from delivery to commissioned operation.

Intelligent Control

Automated System Monitoring. Hands-Free Reliability.

The PLC-based Intelligent Control Console keeps the SR 36-S stable around the clock and gives operators full visibility when it matters.

  • Precise thermostatic control
  • Adaptive flow control
  • Automatic preheating control
  • External cooling system linkage
  • Historical alarms & operation records
  • Historical performance data curves
  • Multi-point fault alarm system
  • Low water level & leak alarms
  • Auto load reduction & recovery on high temp
  • Unified component status overview
  • O&M operation permission groups
  • Indoor & outdoor environment monitoring
SR 36-S · CONTROL CONSOLE STABLE
Coolant Temp90.3 °F
Flow Rate20.0 m³/h
Pump Load68%
09:41:07  OK  Fan array frequency 46.2 Hz — auto-adjusted
09:40:52  OK  Water level nominal — tank 92%
09:40:31  OK  All 36 slots online — load balanced

Illustrative interface. Values shown are representative operating data.

Technical Specifications

SR 36-S at a glance

Full system parameters for capacity, physical dimensions, electrical input, and control.

Capacity & Cooling
Miner capacity36 unitsAntminer S19 / S21 Hydro series
Heat dissipation capacity> 200 kW
Total load210 kWIncluding cooling energy consumption
System energy consumption10 kW
Design PUE< 1.05
Fans2 large-volume fans
Constant-temperature modeVariable-frequency AC fan controlPlus stepwise EC fan regulation
Physical & Dimensions
System compositionRack ×1 + CDU and PLC ×1 + dry cooler ×1Includes external piping
Rack dimensions (L×W×H)1650 × 600 × 2150 mm65.0 × 23.6 × 84.6 in
Rack weight325 kg717 lbs
CDU dimensions (L×W×H)600 × 1050 × 2150 mm23.6 × 41.3 × 84.6 in
CDU weight250 kg551 lbs
Dry-cooler dimensions (L×W×H)2600 × 1850 × 2000 mm102.4 × 72.8 × 78.7 in
Dry-cooler weight800 kg1,764 lbs
Installation methodIndoor rack and CDU with outdoor dry cooler
Electrical
Input power3-phase 380–415 V, 50/60 Hz
Miner breakers16 A × 36
Pump power3 kWCDU pump rated 20 m³/h
Water tank70 L stainless steelStorage, pressure storage, water-gas separation and preheating
Network2 × 24-port Gigabit switches
Control & Environment
Control systemPLC control consoleTouchscreen water-temperature, differential and pressure settings
Ambient operating range−4 °F to 113 °F
Evaporation padStandard configuration
CertificationUL / CE certification

Specifications are subject to continuous improvement. Custom configurations available on request.

Applications

Where the SR 36-S performs

Hydro Mining Facilities

High-Density HPC & AI Compute

Energy-Integrated Computing Sites

Remote Sites with Limited Staff

Next Step

Ready to deploy the SR 36-S?

Talk to an engineer about your site, power capacity, and target timeline. We'll help you size the right configuration — and get you a quote fast.

Talk to an Engineer →